Home > Canopy Hatch Latch 5-Pack

Canopy Hatch Latch 5-Pack

Canopy Hatch Latch 5-Pack

Whether you are finishing a foam build or replacing a catch that has finally given up, this five-piece set keeps spares on the bench. Each rc canopy lock is molded in lightweight plastic with an L23.5 mm body and a single 3 mm hole, so one rc canopy latch seats the shell against the fuselage and lifts free for battery changes, receiver swaps and servo checks, with no spring, threaded insert or special tool required.

  • $2.89Listed price
  • 5 pcsPer pack
  • L23.5 mmBody length
  • 3 mmMounting hole
5 Pcs Canopy Hatch Lock Latch L23.5mm For RC Airplanes Parts Electric Planes Foam Model Accessories Color White Black

Three finishes, one shared footprint

Black, white and natural are listed as separate options, but the latch body and the single mounting hole are the same on all three, so the choice is about the airframe, not the fit.

Black-5 Pcs

Five black latches for dark foam cowls and shadowed hatch lines, where a scuffed catch is less obvious between flying sessions.

White-5Pcs

Five white latches that read clearly against dark fuselages, useful when you want to spot the catch quickly during a pre-flight check.

Natural-5Pcs

Five natural molded latches for builders who paint or tint their own shells and want the fastener to sit quietly under a finish.

Same body, same hole, any color

Because all three finishes share the L23.5 mm body and the 3 mm mounting hole, you can switch color later without re-drilling the fuselage side. Buy the pack that matches today’s build and keep the spare latches for the next one.

5 Pcs Canopy Hatch Lock Latch L23.5mm For RC Airplanes Parts Electric Planes Foam Model Accessories Color White Black
L23.5 mm body 3 mm single hole 5 pcs per pack

Dimensions, pack size and spec sheet

These are the numbers that decide whether the latch clears your hatch lip and sits flat on the fuselage side. Everything below is listed on the product page for SKU 011-01302B.

SKU 011-01302B
Pack quantity 5 pcs
Length L23.5 mm
Mounting hole 3 mm, single hole
Mounting method Pin, screw or wire catch through the one hole
Material Lightweight molded plastic
Color options Black-5 Pcs, White-5Pcs, Natural-5Pcs
Compatibility RC airplanes, electric planes, foam models, built-up airframes, glass or plastic canopies
Listed price $2.89

Which airframe is this for?

The same latch covers three common hatch situations. Pick the one that matches your build to see what the part actually does for you.

01

Molded foam hatches

The latch is listed for foam models and seats the canopy shell against the fuselage with a single anchor point.

Buyer decision: one 3 mm hole means one clean mount in the foam shell, and the 5-pack covers a spare in case a catch is knocked loose in transit.

02

Glass or plastic canopies on electric sport models

The listed compatibility covers glass and plastic canopies, and the latch lifts free for battery changes, receiver swaps and servo checks.

Buyer decision: if you open the hatch between every flight, judge the latch on release feel and on holding the canopy against chatter in airflow.

03

Built-up airframes with worn catches

The product page names traditional built-up airframes with worn catches as a use case, and the pack supplies five latches.

Buyer decision: replacing a tired catch is a straight swap of the latch, and the extra four pieces stay in the field box as spares.

Choose your mounting method

All three methods use the same single 3 mm hole, so the decision is about how often you open the hatch, not about the part.

Pin

A pin through the 3 mm hole gives a quick anchor where the latch is taken off and refitted regularly, such as between battery packs.

No threaded insert required.

Screw

A screw through the same 3 mm hole fixes the latch to the fuselage side for a build you want to leave assembled and fly as-is.

No spring or special tool required.

Wire catch

A wire catch through the hole suits airframes where access is tight and you want a light anchor that follows the fuselage line.

One hole, three options.

White canopy hatch lock latch, five-piece pack

Change color without re-drilling

Black, white and natural share the same body and mounting hole. That means a color change is a parts swap, not a second hole in the fuselage side, and the pilot who rebuilds or repaints a model keeps the same anchor point.

  • Black-5 Pcs
  • White-5Pcs
  • Natural-5Pcs
Choose your color

Related Reading

Three notes to help clarify product requirements before contacting the supplier.

How Do Single-Hole Canopy Latches Hold an RC Airplane Canopy?

A single-hole canopy latch holds an RC airplane canopy by locating the shell, pressing it toward the fuselage, and letting contact friction resist small movement.

Read article

Why Does a Single-Hole Canopy Latch Suit Foam Model Builds?

A single-hole canopy latch suits foam model builds by setting alignment with one mounting point, reducing hardware steps, and allowing a dry fit before final fixing.

Read article

Sizing an RC Canopy Lock with a 23.5 mm Length for Hatch Latch Openings

A replacement rc canopy latch fits when its L23.5 mm length and 3 mm mounting-hole reference match the old hatch latch and canopy opening on your RC airplane.

Read article

Frequently Asked Questions

what is included in the five-piece canopy hatch lock set?

each pack contains five canopy hatch lock latches in the selected finish. the latch body is molded in lightweight plastic and measures l23.5 mm, with a 3 mm single mounting hole on every piece.

which rc airplanes and canopies is this latch designed for?

the latch is listed for rc airplanes, electric planes, foam models, built-up airframes, and glass or plastic canopies. it suits molded foam hatches as well as traditional airframes where the old catch is worn.

how does the latch secure and release the canopy?

when seated, the latch holds the canopy shell against the fuselage and helps prevent lifting or chattering in airflow. a simple lift releases the hatch for battery changes, receiver swaps, and servo checks.

what mounting hole and hardware does the latch need?

it uses a single 3 mm mounting hole for a pin, screw, or wire catch that anchors the latch to the fuselage side. no spring, threaded insert, or special tool is required.

what are the exact dimensions and pack quantity?

the latch is l23.5 mm long, and each pack contains 5 pcs. the body is molded from lightweight plastic, and the black, white, and natural finishes share the same body and mounting hole.

can i change the latch color without re-drilling the fuselage?

yes. black-5 pcs, white-5pcs, and natural-5pcs use the same body and mounting hole, so you can change color later without adding a new hole or changing the anchor point.